Dynamic Wire Harness With TE AMP Connectors 5000 TAB 6POS KEY - YY PNL 10WG - 5G Pich 10.16

D-5200 Series (Continued) AMP Dynamic Series Connectors D-5000 Series Performance Characteristics and Specifications Wire AWG #16 16A #14 19A #12 25A #10 Current 30A 6 position max. D-5200S/M Performance Characteristics Pitch Description Voltage Rating Contact Resistance Operating Temperature Dielectric Withstanding Voltage Current Rating 400mils (10.16mm) 630V AC 2mΩ Max. -55°~+105°C 3,000V AC (1 minute) Material and Finish Receptacle Contact Tab Contact Tab Post Housing Material Copper alloy Copper alloy UL 94V-0 rated, glass filled polyester (PBT) Gold plating with underplated nickel Gold plating with underplated nickel

D-5200 Series (Continued) AMP Dynamic Series Connectors D-5000 Series ➀ Insert Extraction Tool in the direction as shown, insert into the narrow lower section of Housing’s reverse convex hole. (make sure that you are holding tool in proper position, top and bottom.) * Take care not to insert tool into contact section. If you’ve inserted by error, replace the contact with a new one before proceeding. D-5 Contacts Application Tooling Crimp Type Contacts Extraction Tool Part Number: 409158-1 Instruction Sheet 411-5774 • How to Use Extraction Tool Receptacle Contact (Used in Receptacle Housing) Tab Contact (Used in Tab Housing) Wire Range AWG mm2 Ins. Dia. Range mm Wire Range Mark Contact Part Numbers* Receptacle Tab Sequential Tab 16 14 12 10 1.25 2.20 3.50 5.50 3~3.8 4~5.2 S M ST. LP. ST. LP. 179955-❏ 316040-❏ 179956-❏ 316041-❏ 917802-❏ 917804-❏ 917803-❏ 917805-❏ Application Tooling Mini-Applicator Hand Tool ** — ** — — 234170-1 — 234171-1 84696-1 1,— 84695-1 1— Note: Enter the following plating code in Part Number suffix-❏: -2 = 0.38 µm thick gold plating, -3 = 0.76µm thick gold plating, -6 = 2.54 µm thick silver plating * Strip Form contacts are used with Mini-Applicator and Loose-Piece contacts are with hand tools. **Mini-Applicator is for use on Automachines. (See next page. Contact Technical Support for details.) •Used to extract contacts from wire type tab / receptacle housing. (Take care when inserting tool as the lance section of D-5 is turned upside down to that of D-3.) •With D-5 contacts only, it is possible to extract using a small-size slotted screwdriver. When Using D-5 Extraction Tool When Using Slotted Screwdriver ➁ The tip of Extraction Tool depresses housing lance, freeing contact. ➂ Contact can now be pulled out. ➁ When you butt the tip of tool at lance section and depress it, contact is released. ➂ Contact can be pulled out. D-5α Contacts (Silver Plating) Wire Range AWG mm2 Ins. Dia. Range mm Wire Range Mark Contact Part Numbers* Receptacle 20 16 16 14 0.50 1.25 1.25 2.20 1.8~3.23 3~3.80 SS S ST. LP. ST. LP. 1318985-6 1318986-6 0179955-6 0316040-6 Application Tooling Mini-Applicator ** — ** — Note: The contact part numbers with "-6" are silver plated with 2.54 µm thickness. * Strip Form contacts are used with Mini-Applicator and Loose-Piece contacts are with hand tools. **Mini-Applicator is for use on Automachines. (See next page. Contact Technical Support for details.) 12 10 8 3.50 5.50 8.00 4~5.2 4.9~7.8 M L ST. LP. ST. LP. 0179956-6 0316041-6 1318696-6 1318697-6 ** — ** — Hand Tool — 91596-1 — 234170-1 — 234171-1 — 1366044-1